![stm32 windows 10 driver stm32 windows 10 driver](https://i.ytimg.com/vi/Sa48sPObmJ0/maxresdefault.jpg)
If your driver isn't working, use the driver having the same OEM with the your laptop/desktop brand name. If you are looking for an update, pickup the latest one. With the different devices, they can have the same driver, it's because they all use the same chip manufacturer. The drivers that were selected are installed in parallel with this installation of STM32CubeIDE from here on. Below is a list of drivers that may be suitable for your device. 6 Gbytes of free hard-disk space for non STM32 MPU OpenSTLinux Distribution developers, 15 Gbytes for. ↳ STM boards (Discovery, Eval, Nucleo.↳ Let us know a bit about you and your projects.So my problem is, i failed to have the USB bootloader working, because when in bootloader MODE, windows cannot recognize the device. But if i tried to flash the blink code to bluepill using external USB to serial TTL (TX & RX connected to PA9 & PA10) in bootloader mode, it succeeded. i tried with other STLINK, bluepill, and USB cable. Windows recognized again as Maple Serial.Ģ1. i turned bluepill off (unplug the USB cable), set the BOOT0 jumper to 0, and then replugged the cable. i was confused, i thought that : Maple serial driver is serial driver when RUNNING MODE, and MAple-DFU driver is serial driver when bootloader MODE.Ģ0.
![stm32 windows 10 driver stm32 windows 10 driver](https://image.easyeda.com/histories/d2b0dc6ed68c479da89fbbfe63dfbbf6.png)
after that, windows had error, USB device not recognized.ġ9. i unplugged the USB cable, switch BOOT0 to 1 (VCC 3.3V), and replugged the USB cableġ8. i thought that this was because the bluepill is on RUNNING MODE (not bootloader MODE)ġ7. compile success,but when i uploaded the HEX, error happened :ġ6. i set the board to Generic STM32F103 series, set upload method : serial, and set the COM Portġ5. i opened Arduino IDE, open blink LED sketch from examplesġ4. After accepting the agreement and choosing the desired location to install the IDE, the installation process will start. zip file you will be asked for your agreement. windows recognized the device as Maple Serial (COMxx)ġ2. A few moments later, after specifying the directory your download will start. Run Zadig and click Options List All Devices. ran install_drivers.bat in folder drivers, succeeded.ġ1. Install a generic USB driver for your device - WinUSB using Zadig. if i unplug and replug the USB cable, the LED on PC13 was blinking fast and then blinking slow, and then OFF (as expected)ġ0. flashed the bin file using command line stlink (i think that using STLINK, it doesnt care if the BOOT0 jumper set to 0 or to 1) and succeeded.ĩ. turned on the bluepill using USB cable which was connected to my laptopĨ. download Roger Clark's Arduino_STM32-master, copied and unzipped it to Documents\Arduino\hardwareħ. i bought 4 bluepill board (china), and changed the 10K resistor to 1K5 resistorĤ. Hello there.i am quite new with bluepill STM32F103 board.ġ. While someone that knows something is reading this, with the generic bootloader named "generic_boot20_pc13" What is the boot20 indicating? I assume where it is jumping to in flash to start execution of the program. Most of the documents I find on the Web use this as an example.
![stm32 windows 10 driver stm32 windows 10 driver](https://axotron.se/blog/wp-content/uploads/2016/08/CubeMX-768x696.png)
I started working on pulling stuff together to use an FTDI device and the UART to load the bootloader. So I feel like the boot loader is in there okay and working as expected.Īll bootloaders have been installed using an ST-LINK2. It does do the super fast blink on powerup and then a slightly slower flash after about 500ms. The last bootloader loaded is labeled generic_boot20_pc13. But I've tried to work through this using a Blue Pill as well. This includes the Maple bootloader and The board is one of my own designs. I have tried several bootloaders actually.